It takes just minutes to change the blade of your Dewalt circularsaw.
Important InstructionsBefore You Change The Blade Dewalt Circular Saw, Here Are Some Tips.
- Before you start, ensure that your circular saw has been unplugged from the power source. If your circular saw is plugged in while you are trying to change its blade, you could be electrocuted or seriously hurt if it comes in contact with water or other conductive materials such as concrete.
- Wear safety glasses and locate a flat surface on which to place the circular saw. This area should be free from any debris or other items that could cause injury to your circular saw blade. Once you’ve found the best spot, move the front handgrip in such a way that it faces away from you at 90 degrees from your legs. Slide the blade bar until it touches the base of the power cord.
- The guard should be flipped over so it fits snugly against the blade assembly and guard rail assembly. It will completely cover them with no gaps along their length.
- Use both your hands to grip the circular saw’s front handgrip. The blade should hang over the work area.
- Use your hands to slide the new blade through the blade holder until the edge touches the shields. To ensure that each shield is properly seated on the blade, inspect both sides. If any of the shields aren’t properly seated, take them out and replace them with a new one.
- Turn off the circular saw. Now, turn it upside down so that you face the rear handgrip. To ensure that your hands can reach the back of the circular saw, tilt it down towards you.
- Take out the metal handle that holds the blade and toss it.
- Before you touch anything, make sure to wear safety glasses. This includes wearing bare feet. Slide the new Dewalt circular saw blade on its horizontal holder until you see it flush against the shield attached to it. You must be careful not to drop your new blade. If you do, you may never find the small pieces.
- After the blade has been attached to the holder, you will need to twirl it around in each direction before you can put it back together.
- Before you plug your circular saw back into your computer, make sure to remove any debris or parts that may be left behind.
A Video Guide On How To Change The Blade Dewalt Circular Saw
This video explains how to change the blade on the Dewalt Circular Saw.
How to make a change blade Dewalt circular saw
Step-by-Step Guide To How To Change Blade Dewalt Circular Saws:
Step:1
If the saw is corded or battery powered, turn it off and remove the battery from the socket. Next, follow the instructions for changing your blade.
Step:2
You can flip your circular saw upside down to see what’s under the hood.
Step:3
You can remove any shields from the side blades by pressing down gently on the little handle thingsies. They will slide in either direction depending on which side they were attached to and how many are there along the blade’s edges. After you’ve put the saw away, make sure those handles are not accessible by anyone else.
Step:4
Using your screwdriver, remove any screws or nuts that are holding the circular saw blade in place. You can then use your screwdriver for the first time to take out all the shields. This will depend on how many shields are held above the blade by the nuts or screws. You should be careful not to drop these tiny hardware pieces in places that could cause them to become lost forever.
Step:5
To avoid losing balance or having everything fall to the ground below, lift both sides of each shield carefully at once. This could cause injury to other parts of your saw. Keep calm and be careful! As you take the shields off the blade, keep them together so everything can be easily set down.
Step:6
You can remove the old saw blade by lifting it up from its holding area. Pay attention to the way it is attached so you know where to place the new one before anything else. It’s up to you what you intend to do with the old blade.
Step:7
The new circular saw blade should be placed in the exact same place as the old one. You can use the pieces you have just taken out to help you find the right position. After resetting each blade shield piece, make sure they are in the same place. Then lock them down by turning them over so that any nuts or screws can be locked into their original positions.
Step:8
You can check that the saw is still in use by turning it over. This will allow you to determine if there is any obstruction to the saw’s movement, such as a loose metal piece inside the housing.
Step:9
Make sure to plug your saw again and check its movements once more.
FAQs:
What Are Some Of The Benefits To Changing The Blade On A Circular Saw?
You can now make better metal cuts with a new blade.
Your blade will cut through more materials, such as wood, plastic or other composites, resulting in better quality results.
How Do You Know When It Is Time To Replace Your Saw Blade?
Your circular saw blade’s teeth will become worn over time if you cut through materials greater than 1/10cm or 3/20cm. It is best to replace it as soon as possible. You might notice that the material that you are cutting sticks to your blade rather than coming off it. This is a sign that your blade needs to be replaced soon.
You may notice chips and other debris flying around after you’ve cut through wood. It is worth checking the sharpness of your saw blades to see if they need to be replaced or re-used later. Because they require you to apply more pressure to them in order to cut through the wood effectively, dull blades can cause more mess than sharp ones.
Conclusion:
When changing the blade of a Dewalt circular-saw, it is important to be careful. Before you begin, make sure the power has been turned off. These simple steps will allow you to change the blade of your Dewalt circular-saw like a pro in no more than a matter of minutes.
- Diamètre : 190 mm.
- Lame TCT 190 mm x 30 mm avec 80 dents.
- Alésage : 30 mm (bagues de réduction de 16, 20 et 25 mm incluses).
- Saignée de 2,4 mm.
- Dents en carbure de tungstène pour une longue durée de vie.
- 210 mm de diamètre
- 80 dents
- 30 mm de diamètre (16, 20, et 25 mm bagues de réduction fournies)
- 2.4 mm saignée
- Dents en carbure de tungstène pour une longue durée de vie
- Profitez de la grande résistance de cette lame de scie circulaire stationnaire...
- Sciez facilement de nombreux matériaux : Cette lame a été conçue pour être...
- Conseils d'utilisation pour un confort de travail optimal : Pour tous vos...
- Des articles qui correspondent totalement aux normes de sécurité en vigueur :...
- Une excellente garantie atteignant les 3 ans en fonction du modèle : Chez...
- Lame circulaire 254 pour coupe bois sur meuleuse angulaire ou scie de table
- Utilisation Lame: bois dur et le bois tendre, plateau recouvert des deux côtés...
- Angle de structure particulière : panneau d'aggloméré de + 10 °, dents...
- Diamètre Disque : 254 mm Alésage 30 mm Epaisseur 2,4 RPM max 6000
- Disque professionnel et decoupe prècise.
- Dimensions : 165 mm de diamètre – 80 dents – Alésage de 20 mm (bague de...
- [Application] – Idéal pour le long du grain et la croix – Coupe sur bois...
- Matériau : corps de lame en acier trempé – Offre une précision et résiste...
- Caractéristiques : intègre un design de dents décalées ATB (biseau...
- Compatibilité : compatible avec Dewalt Bosch, Makita, Ryobi et toute autre scie...
- Lame de scie circulaire en carbure de tungstène trempé et durci de qualité...
- 185 mm de diamètre x 80 dents.
- Alésage de 20 mm (anneau de réduction de 16 mm inclus).
- Dents en carbure de tungstène pour une plus longue durée de vie.
- Compatible avec : Evolution, Bosch, Makita, Guild, Skil et beaucoup d'autres...
- 160mm de Diamètre
- Lame 1 = 36 dents. Blade 2 = 48 dents. Lame 3 = 60 dents
- 20mm alésage (anneaux de réduction de 16mm inclus)
- 2.4mm saignée
- Dents en carbure de tungstène pour une durée de vie optimale
- Dimensions : 165 mm de diamètre - 24, 36, 48 et 60 dents - Alésage de 20 mm...
- Application : idéal pour couper en croix et le long du grain sur le bois...
- Matériau : corps de la lame en acier trempé – offre une précision et...
- Caractéristiques – Intègre un design de dents décalées ATB (biseau...
- Compatibilité : compatible avec Festool, Dewalt Bosch, Makita, Ryobi et autres...
- Diamètre : 250 mm.
- 80 dents.
- Alésage : 30 mm (bagues de réduction de 16, 20 et 25 mm incluses).
- Trait de scie : 2,8 mm.
- Dents en carbure de tungstène pour une longue durée de vie.
- Diamètre : 160 mm.
- Alésage 20 mm (bague de réduction 16 mm incluse).
- 80 dents.
- Dents en carbure de tungstène pour une longue durée de vie.
- Entraînement : 2,4 mm.
